C-clamp and a block of wood.sweetandsour wrote: ↑13 May 2022, 21:36 I took the tire off of my grandsons F-150 and the outer brake pad was completely gone. The rotor was beyond gouged. We replaced the rotor, put on the new pads, but can't get the pistons compressed back in, they're stuck/seized completely extended and we can't budge them, even with the brake bleed stem open. Any ideas? Or should we just buy new calipers. It's another $200 if we replace both front calipers.
The Gearhead Thread
- jmg
- Resting Mercenary face
- Posts: 554
- Joined: 08 Apr 2022, 15:35
- Has thanked: 32 times
- Been thanked: 175 times
The Gearhead Thread
"When you're dumb, you've got to be tough." -My dad
"No reserves. No retreats. No regrets." -William Borden
"No reserves. No retreats. No regrets." -William Borden
-
- Usher
- Posts: 2961
- Joined: 08 Apr 2022, 03:59
- Has thanked: 325 times
- Been thanked: 356 times
The Gearhead Thread
Thanks, but I have an old store bought c clamp thing, plus a regular c clamp with an old brake pad, but we can't budge it. I think I'll just replace the caliper rather than chance that old one seizing again while in service.jmg wrote: ↑13 May 2022, 22:22C-clamp and a block of wood.sweetandsour wrote: ↑13 May 2022, 21:36 I took the tire off of my grandsons F-150 and the outer brake pad was completely gone. The rotor was beyond gouged. We replaced the rotor, put on the new pads, but can't get the pistons compressed back in, they're stuck/seized completely extended and we can't budge them, even with the brake bleed stem open. Any ideas? Or should we just buy new calipers. It's another $200 if we replace both front calipers.
The Indians will not bother you now, on account of ... you are touched.
- jmg
- Resting Mercenary face
- Posts: 554
- Joined: 08 Apr 2022, 15:35
- Has thanked: 32 times
- Been thanked: 175 times
The Gearhead Thread
If you can't budge it with a c-clamp, then it is really stuck. Sorry, bud. I'm not aware of another way to do it without damaging them.sweetandsour wrote: ↑14 May 2022, 04:14Thanks, but I have an old store bought c clamp thing, plus a regular c clamp with an old brake pad, but we can't budge it. I think I'll just replace the caliper rather than chance that old one seizing again while in service.jmg wrote: ↑13 May 2022, 22:22C-clamp and a block of wood.sweetandsour wrote: ↑13 May 2022, 21:36 I took the tire off of my grandsons F-150 and the outer brake pad was completely gone. The rotor was beyond gouged. We replaced the rotor, put on the new pads, but can't get the pistons compressed back in, they're stuck/seized completely extended and we can't budge them, even with the brake bleed stem open. Any ideas? Or should we just buy new calipers. It's another $200 if we replace both front calipers.
"When you're dumb, you've got to be tough." -My dad
"No reserves. No retreats. No regrets." -William Borden
"No reserves. No retreats. No regrets." -William Borden
-
- Usher
- Posts: 2961
- Joined: 08 Apr 2022, 03:59
- Has thanked: 325 times
- Been thanked: 356 times
The Gearhead Thread
I agree. I bought new calipers to go with the new rotor and pads. I failed to wipe down the new calipers with brake cleaner however, and when the rotor got hot the light oil volatized and produced some white smoke from underneath the wheel well. All is ok now though I hope.jmg wrote: ↑14 May 2022, 13:09If you can't budge it with a c-clamp, then it is really stuck. Sorry, bud. I'm not aware of another way to do it without damaging them.sweetandsour wrote: ↑14 May 2022, 04:14Thanks, but I have an old store bought c clamp thing, plus a regular c clamp with an old brake pad, but we can't budge it. I think I'll just replace the caliper rather than chance that old one seizing again while in service.
The Indians will not bother you now, on account of ... you are touched.
-
- Usher
- Posts: 2961
- Joined: 08 Apr 2022, 03:59
- Has thanked: 325 times
- Been thanked: 356 times
The Gearhead Thread
Is it a sin to curse the engineer that selected the location for the oil pressure sensor on the 2011 GMC Sierra? If so, then may God please forgive me.
Edit:. Ok I finally accidentally broke the electrical connector, then discovered that my deep well 27mm socket wouldn't fit. I had to go buy a special oil pressure sensor socket for $12, which appears to be a 27mm deep well socket but with smaller diameter body, and some rounded edges.
I've got the socket on, with u-joint, extension, and ratchet, all attached, and I can't budge it loose. I'll get my 16 year old grandson over tmrw to give a try.
Edit:. Ok I finally accidentally broke the electrical connector, then discovered that my deep well 27mm socket wouldn't fit. I had to go buy a special oil pressure sensor socket for $12, which appears to be a 27mm deep well socket but with smaller diameter body, and some rounded edges.
I've got the socket on, with u-joint, extension, and ratchet, all attached, and I can't budge it loose. I'll get my 16 year old grandson over tmrw to give a try.
The Indians will not bother you now, on account of ... you are touched.
- joegoat
- The Naughty Grand Poobah
- Posts: 733
- Joined: 09 Apr 2022, 21:04
- Has thanked: 34 times
- Been thanked: 89 times
The Gearhead Thread
I don't know if you've heard it, but there's a saying amoung mechanics. "An engineer will crawl over a pile of 500 virgins just to {zederated} a mechanic." It's true.sweetandsour wrote: ↑17 Jun 2022, 14:56 Is it a sin to curse the engineer that selected the location for the oil pressure sensor on the 2011 GMC Sierra? If so, then may God please forgive me.
Edit:. Ok I finally accidentally broke the electrical connector, then discovered that my deep well 27mm socket wouldn't fit. I had to go buy a special oil pressure sensor socket for $12, which appears to be a 27mm deep well socket but with smaller diameter body, and some rounded edges.
I've got the socket on, with u-joint, extension, and ratchet, all attached, and I can't budge it loose. I'll get my 16 year old grandson over tmrw to give a try.
Quando Omni Flunkus Moritati (When all else fails, play dead)
- joegoat
- The Naughty Grand Poobah
- Posts: 733
- Joined: 09 Apr 2022, 21:04
- Has thanked: 34 times
- Been thanked: 89 times
The Gearhead Thread
Update on the 1949 Gravely Model L restoration.
- Attachments
-
- IMG_20220704_154310972.jpg (1.29 MiB) Viewed 279021 times
Quando Omni Flunkus Moritati (When all else fails, play dead)
- joegoat
- The Naughty Grand Poobah
- Posts: 733
- Joined: 09 Apr 2022, 21:04
- Has thanked: 34 times
- Been thanked: 89 times
The Gearhead Thread
Not sure I ever posted the final results. This the the Gravely cutaway I was working on. Lots of labor involved, but it came out pretty good!
- Attachments
-
- IMG_20220622_145345193 (1).jpg (1.37 MiB) Viewed 279020 times
Quando Omni Flunkus Moritati (When all else fails, play dead)